精品国产av最大网站-精品国产sm最大网免费站-精品国产v无码大片在线观看-精品国产v无码大片在线看-精品国产不卡在线观看免费-精品国产成人av在线

0512-68559199
服務時間 8:00-18:00 (工作日)

比重計/水分儀

EH-300電子比重計-固體

u 技術參數:1. 密度解析:0.001 g/cm32. ZUI大稱重:300g3. ZUI小稱重:0.005 g/0.01 gu 特點:o 直讀任何固體物質的密度值、體積、百分比o PVC顆粒、EVA發泡體、粉末、薄

EH-300電子比重計-固體
當前位置: 首頁 » 試驗解決方案 » 技術文章 » 正文

PV3987高光耐磨測試方法

日期:2023-03-17  1507人瀏覽
放大字體  縮小字體

Scrub Resisitance(Micro-Scrach Resistance)of High-Gloss Surfaces in the Vehicle interrior
 

CRS-RAT往復式磨耗試驗機

Preface
This satandard supersedes the “Audi AG Provisional Test Specification”and Test Specification PV3975(“Matindale Scrub Resistance”)
Previous issues
PV3987:2016-08
Changes
The folloowing changes have been made to PV3987:2016-08
- section 3.1“Test equipment”:exanple changed
1 Scope
This PV describes a method for testing the micro-Scratch resistance and scrub resistance on high-gloss surfaces
A surface is referres to as high-glossy if the gloss level measurement at an angle of 60° is >70GU。Further gloss level measurements are performed with a measuring angle of 20°
 
This test method is suitable for determining the properties of uncoated (Eg PA PMMA)and coat-ed high-gloss surfaces (eg paint ,in-mold decoration(IMD),in-mold labeling(IML))when they are exposed to low-force friction loads。The load is roughly equivalent to that of the cleaning process the test must be performed on plane surfaces
 
The test determines the relative chang in gloss that is generated by rubbing/Scrubbing with polishing paper on the high-gloss surface
 
2 Designation
Scrub resistance (Micro-scratch resistabce)as per PV3987
 
3 Testing
3.1 Test equipment

Test  equipment Crochmeter as per DIN EN ISO105-X12 or a different testing device with which the required test conditions can be set(testing force 9N,Testing path:104±3mm)
Test  head Rubbing adapter C as per DIN55654 (see figure1)
Test equipment/rubbing medium Rolishing paper as per DIN55654:Abrasive grain made of aluminum oxide,semi-open coat density of grain,grain 5um,bonding of grain with full synthetic resin on flexible ,extruded PES film (eg 3M261X)
Cut the polishing paper to an exact width of 25mm and a minimum length of 75mm
Gloss measuring device Measure the gloss level using a reflectometer (as per DIN EN ISO 2813) at angle of 20°

 












 



135681 (Rubber Adapter per DIN55654)2
3.2 Specimen preparation

A minimum Specimen size of 150mmx100mm is required to perfprm the test
Conditioning
There must be at least 7 days between specimen preparation and testing
For conditioning ,plan for 45h in a standard atmosphere as per VW50554-23/50-2 condition hydrophilic materials(eg polyamides)for 7 days in a standard atmosphere
Specimen preparation
Clean the specimen gently under luder lukewarm running water using only your wet hand
 
A mild laboratory flushing agent that does not leave a greasy residue can be used as a cleaning agent
The surfaces to be tested must not be damaged as a result of cleaning
Then rinse the specimen thoroughly with clear water
Dry the specimen by blowing it off with oil-free compressed air
After cleaning,condition hydrophilic materrials once again for 24h in a standard atmosphere

 

3.3 Test procedure
1 condition (see section3.2)
2 clean (see section3.2,for hydrophilic materials ,repeat conditioning if necessary)
3 Meassure the gloss level befor scratching,Measure the gloss level at a measuring angle of 20°
4 Rub/Scratch:Befeor each rubbing process,Clamp in a new rubbing medium。One rubbing
 Process comprise 5 double strokes。Rub with a load of 9N。If the rubbed track is not uniform
(streaky spotted),perform a repeat test
5 After rubbing,store the specimens at room temperature for 24h
6 Measure the gloss level on the track 。Align the gloss measuring device in such a way
 That  themeasuring direction is 90° relative to the rubbing direction。Make sure that the measuring hole of the gloss measuring device rests on the rubbed surface。Do not measure the first and last 10mm of the rubbed track。
 
3.4 evaluation/assessment
Determine the scrub resistance as a relative change in gloss level(%)with respect to the initial
Gloss level。The measuring angle is 20°
Calculate the relative change in gloss level as follow:
(initial gloss level - gloss level after rubbing)x 100 / initial gloss level
 

 

4 Applicable documents
The following documents cited in this standard are necessary to its application
Some of the cited documents are translations from the German original。The translations of German terms in such documents may differ from those used in this stand,resulting in terminologocal inconsistency

 
 
[ 試驗解決方案搜索 ]  [ 加入收藏 ]  [ 告訴好友 ]  [ 打印本文 ]  [ 關閉窗口 ]

本文位置:試驗解決方案
注:蘇州亞諾天下儀器有限公司專業從事試驗室品管檢測設備研發生產!有相對豐富的經驗、有實力強大的團隊、有超強的生產管理能力,選購試驗室檢測設備首選蘇州亞諾天下儀器。我們愿竭誠為您服務+86-512 6855 9199,您的滿意是我最大的追求。
參與評論
©2010-2022 亞諾天下™ 版權所有蘇ICP備11049648號-14 首頁 | 關于我們 | 總經理致辭 | 企業文化 | 服務支援 | 成功案例 | 人才戰略 | 聯系方式 |
 
主站蜘蛛池模板: a级在线观看 | 国产成人午夜极速观看 | 蜜桃臀无码内射一区二区三区 | 欧美综合天天夜夜久久 | 黄色免费一级播放片 | 亚洲av色无码乱码在线观看 | 久久久久久久久无码精品亚洲日韩 | 午夜精品成人一区二区视频 | 免费视频爱爱太爽了 | 国产欧美一区二区精品性色 | 日本高清免费在线视频 | 国产h视频在线观看 | 少妇被粗大的猛烈进出69影院一 | 欧美 日韩 国产 亚洲 色 | 欧美另类视频一区二区三区 | 色一色在线观看视频网站 | 日韩在线 | 中文 | 成年人在线观看视频 | 亚洲日本黄色片 | 天天更新 | 99久久婷婷国产综合精品青草免费 | 成人sese| 女被男啪到哭的视频网站 | 国产精品186在线观看在线播放 | 成年人黄色毛片 | 久久免费精品视频在线观看 | 99精品高清不卡在线观看 | 蜜臀aⅴ国产精品久久久国产老师 | 欧美在线视频免费播放 | 日韩人妻无码免费视频一区二区三区 | 精品卡一卡二卡四卡三卡 | 国产熟睡乱子伦午夜视频 | 日日摸夜夜爽久久综合 | 国产日本欧美在线观看 | 久草在线视频福利 | 久久久久麻豆v国产精华液好用吗 | 无码 人妻 在线 视频 | 久久久久成人精品免费播放动漫 | 欧美在线观看黄色 | 欧美午夜伦理 | 午夜国产精品视频 |